- Home
- ยป
- Products & Services
- »
- Pneumatically Operated Oil Pumps
Pneumatically Operated Oil Pumps
Lubricating Oil Pump
Product Brochure
Pumping station, piping, does feeder, end pressure relay . Pressure reducing valve are fitted as per decided scheme and the items are connected with control panel. When pump is started grease shall be delivered to first main line and it will finally reach to connected lubricating points through dose feeder. Once grease is delivered to all points pressure in the line starts rising as pump is still supplying grease. As soon as pressure crosses set pressure value , pressure reversing value , through control panel actuates. Grease starts flowing into second line. Delivery of grease to lubricating points takes place and pressure rises again. When it crosses set pr. Of end relay, system stops. Cycle is over and all points are lubricated. Now after preset 'OFF' time, system starts again and repeats above sequence.
Manual Pumps: (Botti Italy Make)
The manual pumps of ZMK series are intended for supplying a dual line centralized lubrication system. These are double-acting pumps, provided with a line- reversing value which is adjustable from 50 to 200 bar and operate automatically as soon as the pressure in the system reaches the maximum value . As these pumps are intended to be used with grease, the reservoir is provided with a grease scraper arm which scraps the grease from the reservoir inner wall.
Features
Denomination | Reservoir Capacity | Output Per Stroke |
ZMK 2 A | 2 lts. | 3.5 gm |
ZMK 5 A | 5 lts. | 3.5 gm |
Pneumatically Operated Lubrication Pump
- It is pneumatically operated pump.
Reservoir is of Aluminium.
Whenever compressed air is given to the pump at the input port, piston moves up and discharges oil rom the outlet.
During OFF time of the compressed air, pump gets recharged, sucking oil from the reservoir.
Mounting of the pump is through 4 holes in vertical position.
There is a built in relief valve in the pump to safeguard it from overloading.
There is a special pressure reducing valve provided with the pump to bring down the pressure towards "O" during OFF time.
Input air pressure | : | 5-6 Kg/cm2 |
Output Oil Pressure | : | 18 Kg/cm2 |
Discharge of Oil Reservoir Capacity | : | 10 cc per stroke 1.7liters |
Material of reservoir Suitable oil viscosity | : | Aluminium casting Between 32 to 680 cSt/40 Deg C |
Additional Information:
- Item Code: PN-600-6
Pneumatic Driven Pumps
Product Brochure
Pumping station, piping, does feeders, end pressure reducing valve are fitted as per decided scheme and the items are connected with control panel. When pump is started grease shall be delivered to first main line and it will finally reach to connected lubricating points through does feeder. Once grease is delivered to all points pressure in line starts rising as pump is still supplying grease. As soon as pressure crosses set pressure value, pressure reversing value, through control panel actuates. Grease starts flowing into second line. Delivery of grease to lubricating points takes place and pressure rises again. When it crosses set pr. of end relay, system stops. Cycles is over and all points are lubricated. Now after preset 'OFF' time, system starts again and repeats above sequence.
PNEUMATICALLY DRIVEN PUMPS
These pumps powered by second pneumatic motor are normally provided with an overpressure line reversing value. They are to supply grease at a pressure of 150 bar to the discharge capacity of 200 to 600 gm/minute at air pressure of 4-7 bar.
There is a provision for grease level sensing. The special line reversing level is settable from 30 to 150 bars by an adjustable screw.
The motor pumps ratio is 30:1. For filling grease into reservoir inlet port is provided at the bottom. Pump has reservoir capacity of 5 ltr. Cycle of the pump is governed by separate electrical/electronic control.
Types and Features
Denomination | Reservoir Capacity | Output Per Stroke |
ZMK 2 A | 2 lts. | 3.5 gm |
ZMK 5 A | 5 lts. | 3.5 gm |
Air Operated Grease Pumps
Features of the model:
- This is a 50:1 pump & will dispense grease at a pressure equaling approx. 40 - 50 times the Air Inlet Pressure
- Recommended for applications requiring volume greasing at high pressures in industry, workshops, farm etc.
- Precision engineered steel pump construction with machined Aluminum air Motor
- CNC machined & 100% factory tested
- Intended use with :
- Light & self Collapsing Grease upto NLGI No. 2.
- Wetted Components-Steel, Brass, Aluminum & Polyurethane
Pneumatically Operated Pump
- It is pneumatically operated pump.
-
Reservoir is of Metallic.
-
Whenever compressed air is given to the pump at the input port, piston moves up and discharges oil rom the outlet.
-
During OFF time of the compressed air, pump gets recharged, sucking oil from the reservoir.
-
Mounting of the pump is through 4 holes in vertical position.
-
There is a built in relief valve in the pump to safeguard it from overloading.
-
There is a special pressure reducing valve provided with the pump to bring down the pressure towards "O" during OFF time.
Input air pressure | : | 5-6 Kg/cm2 |
Output Oil Pressure | : | 18 Kg/cm2 |
Discharge of Oil Reservoir Capacity | : | 10 cc per stroke 3liters |
Material of reservoir Suitable oil viscosity | : | Mild Steel Between 32 to 680 cSt/40 Deg C |
Additional Information:
- Item Code: PN-600-60