Srujana Industrial Marketing Associates

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer),D/P

• This pump has its own reservoir
• It is piston type, where piston is actuated by a cam, integral with the handle of the pump
• On operating the handle, pump discharges oil
• As soon as the pulling force on the handle is released, piston returns back by spring force and the pressure in the lubrication line is reduced to 1kg/sq.cm. and so on
• There is an in-built check valve and pressure reducing system in corporate in the pump
• Pump is also equipped with relief valve, which safeguards it from overloading
• Pump is also fitted with an oil window to crosscheck the level of oil in the pump and to refill the reservoir from the top opening, once the oil level is nearing the minimum point
• Pump is also equipped with a suction strainer at the inlet and a drain plug at the bottom of the reservoir
• Suitable mounting holes are provided for vertical mounting of the pump
• Pump outlet is suitable for 6 mm dia tube
  
  

  Pressure	15 Kg/cm2
  Discharge	10 cc per stroke
  Reservoir	1700 cc
  Material of Reservoir	Aluminum Casting

Additional Information:

• Item Code: H-1700-10

• This pump has its own reservoir.
• It is piston type, where piston is actuated by a cam, integral with the handle of the pump.
• On operating the handle, pump discharges oil.
• As soon as the pulling force on the handle is released, piston returns back by spring force and the pressure in the lubrication line is reduced to 1kg/sq. cm. and so on.
• There is an in-built check valve and pressure reducing system in corporated in the pump.
• Pump is also equipped with relief valve, which safeguards it from overloading.
• The total pump is made out of S.S. Material i.e, body of the pump is S.S., piston and cylinder in S.S. while the rubber parts are viton.
• Suitable mounting holes are provided for vertical mounting of the pump.
• Pump outlet is suitable for 6 mm dia tube.
• The pump is suitable for water operation as well as other chemicals.

Additional Information:

• Item Code: H-2000-10

• This is a simple pump meant for delivering oil in lubrication line
• It is ideally suited for general purpose machine, where pump can be inserted into oil reservoir of the machine or can be mounted separately in machine casing below the reservoir
• The pump is actuated by hand pull and release of handle for as many times as per lubrication requirement
• It is advisable to attach a suction strainer before the inlet of the pump to avoid damage to pump's piston. This strainer is supplied as optional accessory
• Relief valve, if required, is available as optional accessory
  
  

  Pressure	15 Kg/cm2
  Discharge	7 cc per stroke

  
  
  Suitable for direct connection of 6mm O.D. Tube

Additional Information:

• Item Code: H-7

• This is a mini hydraulic power pack fitted with a motor and rotary positive displacement pump.
• The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.
• Unit is fitted with a suitable pressure switch, float switch and oil window for checking oil level.
• During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, for safeguarding the system from over–loading and the pressure can be read on the Pressure Gauge fitted on the unit.
• During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on.
• The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.
• For vertical mounting of the unit, four holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump.
• Unit is supplied with an adopter (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6mm OD tube.
  
  

  Discharge of Pump	1 L.P.M.
  Reservoir Capacity	3 ltrs. ( In Mild Steel)
  Motor	0.12 KW, 4 Pole,1500 rpm, 3 Phase, 415 V
  Relief Valve	Pre set at 15-18 kg/sq.cm.
  Pressure Switch	42 V (Max), 0.2 Amp (Max), Pre set at 12kg/sq. cm 1 NO 1 NC contact.
  Float Switch	220 V (Max.) 0.2 Amp (Max.), NC contact.
  Suitable oil Viscosity	Between 32 to 220 cst/40c

Additional Information:

• Item Code: ALU-03

• Suitable reservoir with baffles.
• Continuous duty motors TEFC.
• Positive displacement pump-gear/lobe type.
• Suitable relief valve to relieve excess pressure.
• Suitable inline filter to clean the oil thoroughly.
• Metering Valves (Progressive feeder) with Indicator Pin.
• Return line filter with clogging indicator.
• Restrictor ejecting oil at Low Pressure.
• Instruments like pressure gauge with isolation valve, pressure switch.
• Oil level switch.
• Heater or Cooler (Optional)
• Control Panel to monitor the pressure, level of oil in the tank, level of filtration as well as houses motor contractor/ relay etc. with auto/manual mode.
• Continuous lubrication systems are in standard models: 20, 30, 50, 75 & 120 liters capacity with 1, 3, 4, 6 & 10 LPM pumps with pressure rating of 5 kg/cm2.

Our customers can avail Hand Pump With Reservoir Model H-600-6 from us. The offered range of hand pump with reservoir model h-600-6 is designed utilizing optimum grade raw material such as timber and allied at reliable vendors' premises. Along with this, the offered range of hand pump with reservoir model h-600-6 is tested on different parameters to maintain its authenticity throughout the manufacturing process.

Specifications:

• This pump has its own reservoir
• It is piston type, where piston is actuated by a cam, integral with the handle of the pump
• On operating the handle, pump discharges oil
• As soon as the pulling force on the handle is released, piston returns back by spring force and the pressure in the lubrication line is reduced to 1kg/sq.cm. and so on
• There is an in-built check valve and pressure reducing system incorporated in the pump
• Pump is also equipped with relief valve, which safeguards it from overloading
• Pump is also fitted with an oil window to crosscheck the level of oil in the pump and to refill the reservoir from the top opening, once the oil level is nearing the minimum point
• Pump is also equipped with a suction strainer at the inlet and a drain plug at the bottom of the reservoir
• Suitable mounting holes are provided for vertical mounting of the pump.
• Pump outlet is suitable for 6 mm dia tube

Additional Information:

• Item Code: H-600-6

• This pump has its own reservoir made of ACRYLIC.
• It is piston type, where piston is actuated by a cam, integral with the handle of the pump.
• On operating the handle, pump discharges oil.
• As soon as the pulling force on the handle is released, piston returns back by spring force and the pressure in the lubrication line is reduced to 1kg/sq. cm. and so on.
• There is an in-built check valve and pressure reducing system incorporated in the pump.
• Pump is also equipped with relief valve, which safeguards it from overloading.
• The acrylic body of pump facilitates the crosschecking of the level of oil in the pump and to refill the reservoir from the top opening, once the oil level is nearing the minimum point.
• Pump is also equipped with a suction strainer at the inlet and a drain plug at the bottom of the reservoir.
• Suitable mounting holes are provided for vertical mounting of the pump.
• Pump outlet is suitable for 6 mm dia tube.

Additional Information:

• Item Code: H-600-6A

• This is a mini hydraulic power pack fitted with a motor and rotary positive displacement pump.
• The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.
• Unit is fitted with a suitable pressure switch, float switch and oil window for checking oil level.
• During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 20-25 bars, with the help of an in-built relief valve, for safeguarding the system from over–loading.
• During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm.
• The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.
• For vertical mounting of the unit, four holes are provided at the back of the system.There is an in-built check valve and pressure reducing system incorporated in the pump.Outlet port is suitable for 6mm OD tube.
  
  

  Discharge of Pump	1 .5 L.P.M.
  Reservoir Capacity	8 ltrs. ( in Mild Steel)
  Motor	0.18 KW, 1500 rpm, 3 Phase, 415 V, Fan cooled
  Relief Valve	Pre set at 20-25 kg/sq.cm.
  Pressure Switch	220 V (Max), 1 Amp (Max), Pre set at 18kg/sq. cm 1 NO + 1 NC contact.
  Float Switch	220 V (Max.) 0.2 Amp (Max.) with 1 NC Contact (Oil filled)
  Suitable oil Viscosity	Between 32 to 680 cst/40c

Additional Information:

• Item Code: ALU-08

• This is a mini hydraulic power pack fitted with a motor and rotary positive displacement pump.
• The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.
• Unit is fitted with a suitable pressure switch, float switch and oil window for checking oil level.
• During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 20-25 bars, with the help of an in-built relief valve, for safeguarding the system from over–loading.
• During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm.
• The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.
• For vertical mounting of the unit, four holes are provided at the back of the system.There is an in-built check valve and pressure reducing system incorporated in the pump.Outlet port is suitable for 6mm OD tube.

Additional Information:

• Item Code: ALU-08CE

• This is mini hydraulic power pack fitted with a motor and rotary positive displacement pump
• The unit is designed for intermittent run only and is best suited for single shot lubrication
• Unit is fitted with a suitable pressure switch, float switch and a transparent reservoir (for visually checking the oil level)
• During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading and the pressure can be read on the pressure gauge fitted on the unit
• During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on
• The system is also provided with a bleed valve near the outlet port to automatically bleed air if entrained in system
• For vertical mounting of the unit, two holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump
• Unit is supplied with an adopter (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6 mm OD tube
  
  

  Discharge of Pump	150 cc / min.
  Reservoir Capacity	1.8 ltr in polycarbonate material
  Motor	25 W, Single Phase, 220 V / 110 V
  Relief Valve	Pre set at 15 kg/sq.cm.
  Pressure Switch	(optional)
  Digital Timer	(optional)
  Float Switch	(optional)
  Suitable oil Viscosity	Between 32 to 460 cSt / 40 degrees celsius

Additional Information:

• Item Code: AR-AMGP-01S

• This is mini hydraulic power pack fitted with a motor and rotary positive displacement pump
• The unit is designed for intermittent run only and is best suited for single shot lubrication
• Unit is fitted with a suitable pressure switch, float switch and a transparent reservoir (for visually checking the oil level)
• During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading and the pressure can be read on the pressure gauge fitted on the unit
• During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on
• The system is also provided with a bleed valve near the outlet port to automatically bleed air if entrained in system
• For vertical mounting of the unit, two holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump
• Unit is supplied with an adopter (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6 mm OD tube
  
  

  Discharge of Pump	250 cc / min.
  Reservoir Capacity	3.0 ltrs. in Polycarbonate Material
  Motor	40 W, Single Phase, 110 / 220 V
  Relief Valve	Pre set at 20 kg/sq.cm.
  Pressure Switch	Built in
  Float Switch	Built in
  Suitable oil Viscosity	Between 32 to 680 cSt / 40 degrees celsius

Additional Information:

• Item Code: AR-AMGP-200NS

• This is a mini hydraulic power pack fitted with a motor and rotary positive displacement pump.
• The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.
• Unit is fitted with a suitable pressure switch, float switch and oil window for checking oil level.
• During ON cycle, (5 sec. fixed), the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, for safeguarding the system from over–loading and the pressure can be read on the Pressure Gauge fitted on the unit.
• During OFF cycle (any time more than 2 minutes -adjustable) the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on.
• The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.
• For vertical mounting of the unit, four holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump.
• Unit is supplied with an adopter (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6mm OD tube.
  
  

  Discharge of Pump	1 L.P.M.
  Reservoir Capacity	3.0 ltrs.
  Motor	0.12 KW, 3 phase, 4 pole, 415 V, 50 Hz
  Relief Valve	Pre set at 15 kg/sq.cm.
  Pressure Switch (CE)	24 V (Max), 0.1 A (Max), Pre-Set at 12 kg/cm2 1NO Contact
  Float Switch	42 V(Max), 0.1 A (Max) (Vertical reed type)
  Pressure gauge	0-25 kg/cm2
  Suitable oil Viscosity	Between 32 to 220 cst/40c

Additional Information:

• Item Code: ALU-CEN-03-CE

• This is mini hydraulic power pack fitted with a motor and rotary positive displacement pump.
• The unit is designed for intermittent run only and is best suited for Single Shot Lubrication.
• Unit is fitted with a suitable pressure switch, float switch and a transparent reservoir (for visually checking the oil level).
• During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 15-20 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading.
• During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on.
• The system is also provided with a Bleed Valve near the outlet port to automatically bleed air if entrained in system.
• For vertical mounting of the unit, two holes are provided at the back of the system.
• There is an inbuilt check valve and pressure reducing system incorporated in the pump.
• Outlet port is suitable for 6mm OD tube.
  
  

  Discharge of Pump	0.70/1 LPM
  Reservoir Capacity	2.7 ltrs./ 3 ltrs. (in translucent PP Material)
  Motor	0.10KW,1400 RPM, Single Phase, 230 V
  Relief Valve	Pre set at 15-20 kg/sq.cm.
  Pressure Switch	42 V (Max), 0.2 A (Max), Pre -set at 12 kg/sq. cm, 1 NO+1NC Contact
  Float Switch	Reed type vertical 42 V (Max), 0.2 A (Max) with 1 NC Contact (Oil Filled)
  Suitable oil Viscosity	Between 32 to 680 cSt / 40 degrees celsius

Additional Information:

• Item Code: ELU-2700

• This is mini hydraulic power pack fitted with a motor and rotary positive displacement pump
• The unit is designed for intermittent run only and is best suited for single shot lubrication
• Unit is fitted with a suitable pressure switch, float switch and a transparent reservoir (for visually checking the oil level)
• During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading and the pressure can be read on the pressure gauge fitted on the unit
• During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on
• The system is also provided with a bleed valve near the outlet port to automatically bleed air if entrained in system
• For vertical mounting of the unit, two holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump
• Unit is supplied with an adopter (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6 mm OD tube
  
  

  Discharge of Pump	0.70/1 LPM
  Reservoir Capacity	2.7 ltrs./ 3 ltrs. (in translucent PP Material)
  Motor	0.10KW,1400 RPM, Single Phase, 230 V
  Relief Valve	Pre set at 15-20 kg/sq.cm.
  Pressure Switch	42 V (Max), 0.2 A (Max), Pre -set at 12 kg/sq. cm, 1 NO+1NC Contact
  Float Switch	Reed type vertical 42 V (Max), 0.2 A (Max) with 1 NC Contact (Oil Filled)
  Suitable oil Viscosity	Between 32 to 680 cSt / 40 degrees celsius

Additional Information:

• Item Code: ELR-2700

• This is mini hydraulic power pack fitted with a motor and rotary positive displacement pump
• The unit is designed for intermittent run only and is best suited for single shot lubrication
• Unit is fitted with a suitable pressure switch, float switch and a transparent reservoir (for visually checking the oil level)
• During ON cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 10-20 bars, with the help of an in-built relief valve, which is also safeguarding the system from over–loading and the pressure can be read on the pressure gauge fitted on the unit
• During OFF cycle the pressure in the lubrication line is reduced to 1 kg/sq.cm. and so on
• The system is also provided with a bleed valve near the outlet port to automatically bleed air if entrained in system
• For vertical mounting of the unit, two holes are provided at the back of the system. There is an inbuilt check valve and pressure reducing system incorporated in the pump
• Unit is supplied with an adopter (outlet port) of M10x1 tapping, fitted with a locking screw and a cone (ferrule), suitable for 6 mm OD tube
  
  

  Discharge of Pump	350 cc / min.
  Reservoir Capacity	3.0 ltrs. (in die cast Aluminium material)
  Motor	0.09 KW, 1500 rpm, 3 Phase, 415 V
  Relief Valve	Pre set at 25 kg/sq.cm.
  Pressure Switch	220 V (Max), 0.1 Amp (Max), Pre set at 20kg/sq. cm, with 1 NO + 1 NC contact.
  Float Switch	42 V (Max.) 0.2 Amp (Max.), 1 NC contact (oil filled)
  Suitable oil Viscosity	Between 32 to 460 cSt / 40 degrees celsius

Additional Information:

• Item Code: LUBPack-3003-PS-FS-AL

• This is a mini hydraulic power pack fitted with a motor and rotary positive displacement pump
• The unit is designed for intermittent run only and is best suited for single shot lubrication
• Unit is fitted with a suitable pressure switch, float switch and oil window for checking oil level.
• During on cycle, the electrically driven pump discharges the oil with high pressure, adjustable between 18-20 bars, with the help of an in-built relief valve, for safeguarding the system from over–loading
• During off cycle the pressure in the lubrication line is reduced to 1 kg/sq. cm. and so on
• The system is also provided with a bleed valve near the outlet port to automatically bleed air if entrained in system
• For vertical mounting of the unit, four holes are provided at the back of the system
• For vertical mounting of the unit, four holes are provided at the back of the system. There is an in-built check valve and pressure reducing system incorporated in the pump Outlet port is suitable for 6mm OD tube
  
  

  Discharge Of Pump	1 l. P. M.
  Reservoir Capacity	5 ltrs.
  Motor	0. 12 kw, 1500 rpm, 3 phase, 415 v
  Relief Valve	pre set at 18-20 kg/sq. Cm.
  Pressure Switch	220 V (max), 1 amp (max), pre set at 15kg/sq. Cm 1 no + 1 nc contact.
  Float Switch	220 V (max. ) 0. 2 amp (max. ) with 1 nc contact (oil filled)
  Suitable Oil Viscosity	between 32 to 680 cst/40c

Additional Information:

• Item Code: ALU-05

Keeping the diverse requirements of customers in mind, we are involved in presenting quality assured assortment of Oil Lubricator. This Oil Lubricator is designed by using cutting edge technology and quality material which we buy from our most trusted and reliable vendors. Our product range is checked for quality under various set norms of the industry. It is customized according to the requirements of our customers.

Features:

• Dimensional accurate
• Reasonable prices
• Superior performance

Keeping in mind the diverse requirements of our clients we are involved in offering an extensive range of Schematic Lubrication System. These are sourced from the reliable vendors of the industry to render maximum client satisfaction. Offered product is highly demanded in market due to their best quality, fine finish and competitive prices.

Features:

• Competitive prices
• Good Quality
• Perfect finish

We have gained immense expertise in delivering Hand Pump With Reservoir Model H-250-4 to our clients. The offered range of hand pump with reservoir model h-250-4 is available in different designs, shapes and sizes to cater to the diverse requirements of esteemed clients. Along with this, the offered range of hand pump with reservoir model h-250-4 is suitably checked on number of characteristics to ensure its conformation with the benchmarks of quality.

Features:

• This pump has its own reservoir

• It is piston type, where piston is actuated by a cam, integral with the handle of the pump

• On operating the handle, pump discharges oil

• As soon as the pulling force on the handle is released, piston returns back by spring force and the pressure in the lubrication line is reduced to 1kg/sq. cm. and so on

• There is an in-built check valve and pressure reducing system incorporated in the pump

• Pump is also equipped with relief valve, which safeguards it from overloading

• Pump is also fitted with an oil window to crosscheck the level of oil in the pump and to refill the reservoir from the top opening, once the oil level is nearing the minimum point

• Pump is also equipped with a suction strainer at the inlet and a drain plug at the bottom of the reservoir

• Suitable mounting holes are provided for vertical mounting of the pump.

• Pump outlet is suitable for 6 mm dia tube

Additional Information:

• Item Code: H-250-4